Welcome To our shop !

HV2891T-BLK-12V – Mini Ollo Black LED Step Light with Eyelid

$60.995 $121.99
SKU: KO80391097351
Availability: in Stock

The Mini Ollo is the smallest recessed step light Havit builds with an eyelid, and this isthe black one. Havit's own description is "Recessed Wall or Step Light With Eyelid",…

Qty:

The Mini Ollo is the smallest recessed step light Havit builds with an eyelid, and this isthe black one. Havit’s own description is “Recessed Wall or Step Light With Eyelid”, and theeyelid is the point: the aperture sits under an integral hood rather than flush and open, so the litface is set back inside the trim. It is a 1W built-in LED on a 30 beam, which makes it amarker light for treads, risers, low walls and pathway edging rather than anything you would light aspace with.

The face is stainless steel with a poly powder coated black finish, over a full 316 stainless steelbody, and the lens is tempered glass. That combination is why the black version costs the same as thebare stainless one and less than the copper: the corrosion-resisting metal is the same in all three, andonly the face treatment changes. The sealed rating is IP67 and the impact rating is IK10.

Cutting it in is the part worth reading before you order. Havit publishes two apertures for thisfitting and they are not interchangeable: 38mm without a canister and46mm with one. Both figures are on the data sheet as published values, so work towhichever way you are mounting rather than to the trim you can see. If you are setting it into concrete,the canister goes in first and finishes flush with the wall.

It runs on 12V DC constant voltage and will not work without a driver. Havit’sinstructions are explicit and in capitals about it “DO NOT CONNECT LIGHT FITTING DIRECTLY TO240V” and they also set a hard limit that people miss: the fitting cannot sit morethan 25m from its driver, or the warranty is void. On a run of markers down a long flightof steps that is a real design constraint, not a formality. Multiple fittings wire in parallel.

The colour temperature is chosen at the moment you wire it, not afterwards. Theneutral cables are marked; you connect the 3000K or 5500K tail for those, or join bothtogether for 4000K, and terminate whatever you did not use so it stays IP rated. Once the joinsare soldered and sealed, the colour is fixed. There is no switch and no remote. Decide across the wholerun before anyone picks up a soldering iron, because a mismatched tread in the middle of a staircasemeans cutting a sealed joint back open.

There is no globe and no socket the LED is built in, so there is nothing to replace andnothing to specify. Every join has to be soldered and sealed in adhesive-lined heat shrink or a gel cap;Havit voids the warranty if it is not, and on an IP67 fitting buried in masonry that is the one step youcannot revisit. Lights For You stocks the black Mini Ollo alongside the copper and stainless faces ofthe same body, so a single stair run can mix finishes without changing the aperture.

Questions

What size hole does it need?

Two figures, both published by Havit, and you need to know which one applies before you cut.Without a canister the cut-out is 38mm. With a canister it is46mm. The canister is the sleeve you set into concrete or masonry so the fittingdrops into a finished hole. If you are going into a stud wall or a timber riser you generally will notuse one. The trim overlaps the aperture in both cases, so measure the fitting or canister you actuallyhave in hand rather than working back from the visible face.

Can I connect it straight to mains?

No. This is a 12V DC constant-voltage fitting and it must be run from a suitable 12V DCconstant-voltage LED driver. Havit’s installation instructions say it in capitals: “DO NOT CONNECTLIGHT FITTING DIRECTLY TO 240V”. There is also a distance rule that matters as much as the driverchoice the fitting cannot be installed more than 25m from that driver, and Havit voids thewarranty if it is. It is Protection Class 3, low voltage, and needs no earth. A licensed electrician hasto do the work.

How do I pick 3000K, 4000K or 5500K?

By which cable you connect, at install time. The neutral tails are marked for colour temperature:connect the 3000K tail for warm white or the 5500K tail for cool white, and join both tailstogether to get 4000K. Whichever tail you do not use has to be terminated so it stays IP rated. Thechoice is permanent once the joins are soldered and sealed there is no switch on this fittingand no remote so settle it for the whole run before the first one goes in.

Can I use it in the ground or in a driveway?

No. Both Havit sheets give the installation type as “Wall – Recessed” and Havit’s own pagecalls it a recessed wall or step light. Nothing published for this model covers being walked on, drivenover, or set into paving where water collects. Havit does make a Mini Ollo for that it is adifferent model, HV2892T, described as a step or inground light so if the fitting needs to gointo the ground, that is the one to look at rather than this one.

Is it dimmable?

Havit lists it as dimmable, on the data sheet, in the installation instructions and on its ownproduct page. What none of those three publish is how there is no dimming protocol, nonamed compatible dimmer and no driver list. Since the fitting takes 12V DC constant voltage and hasno control gear of its own, any dimming happens on the supply side, at the driver and its control. Wehave not filled that gap with a guess: check the dimming specification of the driver you intend to pairit with.

Can I install it near the coast?

Here is exactly what the documents say, because the answer is narrower than a yes or a no. Thesalt-water rule in Havit’s instructions for this fitting reads “Aluminium and 304SS fittings must notbe installed within 5km of any salt water environments” and this fitting is neither. Itsbody is 316 stainless steel. So that clause does not name it, and we have not applied it. Equally, Havitpublishes no coastal approval for this model, so we are not claiming one. What does apply in any exposedposition is the maintenance condition below.

The face is black, so does the stainless maintenance rule still apply to it?

Yes. Havit’s instructions are unqualified on this “All 316 stainless steel fittings musthave regular cleaning maintenance to avoid any tea staining from forming on fitting”, and the sameline adds that “Warranty does not cover Tea Staining”. The powder coating is on the face; thebody underneath it is 316 stainless, so the fitting is covered by that clause regardless of what colourthe visible trim is. Wash it down with clean water as part of normal outdoor maintenance and more oftenanywhere salt or grit is carried onto it.

Only logged in customers who have purchased this product may leave a review.

Shipping policy for our store

We offer fast and reliable shipping worldwide. All orders are carefully packaged and shipped within 1–3 business days after payment confirmation.

  • Fast shipping within 1-3 business days
  • Free shipping on orders over $40
  • 30 days money back guarantee
  • 24/7 online customer support
  • Secure packaging & safe delivery

Standard shipping, expedited shipping and express delivery options are available at checkout. Delivery time depends on your destination country and local logistics.