Welcome To our shop !

Swap-Sleek 8W LED Dimmable Downlight Satin Chrome / Tri-Colour

$12.792 $15.99
SKU: KO80391098159
Availability: in Stock

The Domus SWAP-SLEEK in satin chrome is a flat-fasciarecessed downlight 8W, 800900lumens,90100mm cutout, 35mm deep, 60 beam,IP44, IK05, dimmable. 35 mm the one that fits where the others do not…

Qty:

The Domus SWAP-SLEEK in satin chrome is a flat-fasciarecessed downlight 8W, 800900lumens,90100mm cutout, 35mm deep, 60 beam,IP44, IK05, dimmable.

35 mm the one that fits where the others do not
  • The three SWAP fascias share an engine, an output and a cutout, and differ only indepth: SLEEK 35mm, STEP 40mm, DEEP56mm.
  • ON A RETROFIT THAT IS OFTEN THE WHOLE DECISION. A ceiling void that tooka 1990s halogen can is not necessarily deep enough for a modern anti-glare fitting, and the depth isdiscovered from the ladder with the old fitting already out.
  • 21 mm LESS THAN THE DEEP IS MORE THAN IT SOUNDS it is thedifference between clearing a joist, a bulkhead lining or an insulation batt and not.
  • REMEMBER THE DRIVER NEEDS ROOM TOO. The fitting depth is 35mm; thedriver sits alongside on a flex and plug and needs somewhere to lie flat where it will not becovered.
What a flat fascia costs in glare
  • GLARE IS GEOMETRY. A flat fascia puts the emitter close to the ceilingplane, so the source is visible from further across the room; a deep one hides it until you are almostunderneath.
  • SO THE SLEEK IS THE HIGHEST-GLARE OF THE THREE, and that matters most where people look upor lie down bedrooms, lounges, low ceilings.
  • IT MATTERS LEAST IN A CORRIDOR, A LAUNDRY, A WALK-IN ROBE OR A KITCHEN, where people aremoving and looking down. Those are also the rooms most likely to have a shallowvoid.
  • THE 60 BEAM HELPS. It is narrower than a general-purpose downlight’s90120, so less light escapes sideways than a flat fascia would otherwiseallow. Plan the spacing tighter to compensate: roughly the ceiling height apart on a2.4m ceiling.
Satin chrome a metal fascia in a ceiling

Satin chrome is a brushed metallic rather than a mirror. THAT MATTERS ON A DOWNLIGHT: a polished chrome fascia catches every light source in the roomand shows as a bright point even when the fitting is off, where a satin finish diffuses those reflectionsinto a soft sheen. On a white ceiling satin chrome reads as a deliberate detail ratherthan a mistake, which plain chrome sometimes does. It suits a kitchen or bathroom withbrushed tapware and handles, where matching the metal is the point. IT DOES NOT DISAPPEAR THE WAY A WHITE FASCIA DOES. If the intention is for thedownlights not to be seen, white is the choice; a metal fascia is a decision to make themvisible.

The cutout range is the point and no record here publishes a cutout
  • 90100mm, from the datasheet. A RANGE MEANS IT DROPS INTO ANEXISTING HOLE ANYWHERE IN IT no re-cutting, no patching, no repainting. 43 products in this catalogue publish a cutout range.
  • WE MEASURED THAT 0 OF 843 PRODUCT RECORDS PUBLISH A CUTOUT AT ALL, against87 datasheets that give one. On a recessed fitting that is the figurethat matters most, because it is the only dimension that cannot be corrected oncecut.
  • SO MEASURE THE EXISTING HOLE BEFORE ORDERING. Over 100mm and thiswill not cover; a larger-fascia fitting or a converter plate is the answer.
  • COMBINED WITH THE 35 mm DEPTH, THIS IS THE MOST RETROFIT-TOLERANT FITTING IN THERANGE the widest hole tolerance and the least depthrequired.
IP44, IK05 and dimming

IP44 covers splashing water from any direction enough for a bathroomoutside the direct wet zones, not a shower enclosure. Confirm the zone with yourelectrician. IK05 is an impact rating, published by only 23 products inthis catalogue about a 0.7-joule knock, which matters during construction and when something longis carried through a room. Dimmable with suitable dimmers on an integrated driver withflex and plug; suitable is the operative word, because a mismatched dimmer gives flickerand buzz rather than a clean failure. 35,000hrs over thirty years at threehours a day.

What is published
Specification Value
Fitting depth 35mm the shallowest of the three
Against STEP 40mm DEEP 56mm
Why 21mm matters Clearing a joist, a bulkhead or a batt
The glare trade Flat fascia = the source is visible further across the room
So it suits Corridors, laundries, robes, kitchens not bedrooms
Cutout 90100mm a range, from the sheet
Catalogue-wide 0 of 843 records publish a cutout 87 sheets do
Most retrofit-tolerant of the range Widest hole tolerance and least depth
Satin chrome Diffuses reflections a polished fascia shows as a bright point when off
IP / IK / life IP44 not a shower zone IK05 35,000hrs
Where it works
  • Shallow ceiling voids 35mm plus driver.
  • Corridors, laundries, robes, kitchens people looking down.
  • With brushed tapware and handles matching metal.
  • Not bedrooms or low lounges take the DEEP.
  • Not in a shower enclosure IP44.
Specifying it

Recessed LED downlight, flat fascia. 8W at 240V AC. 800/900/850lm at3000/4000/5700K switchable. CRI 80, 60 beam. Cutout 90100mm, fitting depth 35mm.IP44, IK05. Clear lens, dimmable driver with flex and plug. 35,000hrs. Satin chrome fascia.Five-year residential warranty per the sheet. AT 35 mm THIS IS THE SHALLOWEST OF THE THREE SWAP FASCIAS, AND ON A RETROFIT THAT IS OFTEN THEWHOLE DECISION. A ceiling void that took a 1990s halogen can is not necessarily deep enough for a modernanti-glare fitting, and the depth is discovered from the ladder with the old fitting already out. 21 mmless than the DEEP is the difference between clearing a joist, a bulkhead lining or an insulation batt andnot. WHAT IT COSTS IS GLARE: a flat fascia puts the emitter close to the ceiling plane, so the source isvisible from further across the room. That matters in bedrooms and lounges and matters least in corridors,laundries and kitchens which are also the rooms most likely to have a shallow void.

Supplied and supported by Lights For You.

Questions

How is it different from the DEEP and STEP?

Depth, and nothing else all three share the same 8W engine, output and 90 to 100mm cutout. SLEEK is 35mm, STEP is 40mm, DEEP is 56mm. On a retrofit that is often the whole decision, because a ceiling void that took a 1990s halogen can is not necessarily deep enough for a modern anti-glare fitting.

Is 21mm really a meaningful difference?

More than it sounds. It is the difference between clearing a joist, a bulkhead lining or an insulation batt and not and the depth is usually discovered from the ladder with the old fitting already out. Remember the driver needs room too: the fitting depth is 35mm, and the driver sits alongside on a flex and plug and needs somewhere to lie flat where it will not be covered.

What does the flat fascia cost me?

Glare. Glare is geometry a flat fascia puts the emitter close to the ceiling plane so the source is visible from further across the room, where a deep one hides it until you are almost underneath. So the SLEEK is the highest-glare of the three, and that matters most where people look up or lie down: bedrooms, lounges, low ceilings.

Where is it the right choice?

Corridors, laundries, walk-in robes and kitchens, where people are moving and looking down and which are also the rooms most likely to have a shallow void. The 60 degree beam helps too, being narrower than a general-purpose downlight’s 90 to 120, so less light escapes sideways than a flat fascia would otherwise allow.

Why satin chrome rather than polished?

A polished chrome fascia catches every light source in the room and shows as a bright point even when the fitting is off, where a satin finish diffuses those reflections into a soft sheen. On a white ceiling satin chrome reads as a deliberate detail rather than a mistake, and it suits a kitchen or bathroom with brushed tapware and handles.

Will it be noticeable?

Yes, and that is the point of a metal fascia. It does not disappear the way a white one does if the intention is for the downlights not to be seen, white is the choice.

What size hole does it need?

90 to 100mm, from the datasheet. A range means it drops into an existing hole anywhere in it, with no re-cutting or patching, and combined with the 35mm depth this is the most retrofit-tolerant fitting in the range. Measure the existing hole before ordering over 100mm it will not cover. Note that no product record in this catalogue publishes a cutout at all: 0 of 843, against 87 datasheets that give one.

Only logged in customers who have purchased this product may leave a review.

Shipping policy for our store

We offer fast and reliable shipping worldwide. All orders are carefully packaged and shipped within 1–3 business days after payment confirmation.

  • Fast shipping within 1-3 business days
  • Free shipping on orders over $40
  • 30 days money back guarantee
  • 24/7 online customer support
  • Secure packaging & safe delivery

Standard shipping, expedited shipping and express delivery options are available at checkout. Delivery time depends on your destination country and local logistics.