Your shopping cart is empty!
The Domus CELL-DT90 is a deep tilt frame for the CELL downlight moduleseries, 909070mm, inblack or white. Cutout 90mm. This is the CELL frame that puts a tilting aperture into…
The Domus CELL-DT90 is a deep tilt frame for the CELL downlight moduleseries, 909070mm, inblack or white. Cutout 90mm.
This is the CELL frame that puts a tilting aperture into an existing90mm ceiling. 90mm is the common Australian downlight hole, so pullout an old halogen fitting, drop this frame in, and click in a CELL module.
Do not confuse it with the CELL-T90, which sounds like it does the same job anddoes not that frame takes 80mm. Within this range the naming isreliable on the D-series and unreliable on the T90, so it is worth being explicit:
| Tilt frame | Cutout | Depth | Use |
|---|---|---|---|
| DT90 (this) | 90mm | 70mm | Retrofit into a standard hole |
| T90 | 80mm | 50mm | New ceiling, shallow void |
One note on sources: the datasheet shared across the CELL frame family gives acutout of 7075mm, which is the S-series figure and does not describe this frame.The title and record are the reliable sources here and that is the reverse of theusual position in this catalogue.
Black recedes into the aperture and reduces the apparent glare of the module behindit; white disappears into a white ceiling. Match the frame to themodule.
Deep tilt frame for the Domus CELL downlight module series.Cutout 90mm. Body 909070mm. Black or white. The common Australian aperture a straight retrofit with a tilt head.
The CELL module and its driver are sold separately. Allow for the module above theframe: Trio 56mm, DALI 68mm. Not to be confused with the CELL-T90 frame, which takes80mm. The shared frame datasheet states 7075mm, the S-seriesfigure, which is not this frame’s. Warranty 3 years.
Supplied and supported by Lights For You.
Will it fit my existing downlight holes?
Very likely 90mm is the common Australian downlight aperture, which is exactly why this frame exists. Pull out an old halogen fitting, drop this frame into the same hole and click in a CELL module, and you have a tilting aperture where the fitting you took out was fixed and sealed. Check the depth above the hole though: 70mm for the frame plus the module.
What is the difference between the DT90 and the T90?
The cutout and the depth, and the names do not help. The DT90 takes 90mm and is 70mm deep a retrofit into a standard hole. The T90 takes 80mm and is 50mm deep a new ceiling, shallow void. If you are working with existing holes, this is the one.
The datasheet says 7075 mm which is right?
The 90mm, from the title and the record. The datasheet is shared across the CELL frame family and its cutout line gives the S-series figure, which does not describe this frame. That is the reverse of the usual position in this catalogue, where the datasheet is normally the reliable source, so it is worth saying rather than leaving you to reconcile them.
What does “deep” give me over a shallow frame?
70mm against 50mm, which sets the lamp back from the ceiling line and reduces glare at a shallow viewing angle the geometry that makes a flush downlight uncomfortable when you walk towards a run. It also shades the aperture, so the fitting reads as a dark recess when off rather than a lit-looking hole. The cost is void depth.
Does it come with a light?
No a frame is not a light. The CELL module and its driver are a separate purchase: CELL-9 or CELL-13, in Trio or DALI. The module carries the beam angle and the five colour temperatures, so a frame plus a module is the only route to a beam other than 60 in this system.
Can I mix it with fixed downlights?
Yes, and that is usually the right approach fixed for the general light, tilt where something needs aiming. The CELL-D90 is the fixed frame at the same 90mm aperture and the same 70mm depth, so a mixed run cuts to one hole size and the trims match.
How much depth do I really need?
The frame’s 70mm plus the module above it 56mm for a Trio module, 68mm for DALI. On a retrofit that is the number to check against what is actually above the existing hole, because the hole itself tells you nothing about the void. Tell us the depth available and the module you want and we will do the arithmetic.
Only logged in customers who have purchased this product may leave a review.
We offer fast and reliable shipping worldwide. All orders are carefully packaged and shipped within 1–3 business days after payment confirmation.
Standard shipping, expedited shipping and express delivery options are available at checkout. Delivery time depends on your destination country and local logistics.