Your shopping cart is empty!
The Domus Maxi 50 is a 1.7m suspended LED linear pendant 34W, 3060lm, 3000K atCRI90, dimmable, in a black body, in six finishes.
Domus asks you to call and confirm it. We will.
| Finish | What happens to shallow-angle light | The light itself |
|---|---|---|
| Frosted / opal | Scattered | Kept but still emitted at that angle |
| Prismatic | Redirected downward | Kept and put to use |
| Honeycomb | Absorbed | Lost |
| Specification | Value |
|---|---|
| Light output | 3060lm 90lm/W |
| Colour rendering | CRI90 at 3000K |
| Power / length | 34W at 240V 1700mm |
| Beam | 120, down only |
| IP rating | IP20 dry interior only |
| Suspension | 3m drop supplied |
| Warranty | 3 years, replacement |
| UGR minimum dim level lifespan | Not published |
1.7m suspended LED linear pendant. 3060lm, 34W (90lm/W), 3000K,CRI90. IP20. 1700mm. 3m drop. PLEX-COB-20W strip, integral dimmable driver, DALI and emergencyon request. Black powder-coated aluminium body. Six finishes. 3-year replacement warranty. Order codeMAXI-50-1.7M-B-3K. PRISMATIC IS A CLEAR PANEL MOULDED WITH SMALL PRISMS THAT REFRACT STEEP RAYS BACK TOWARDS THEVERTICAL it REDIRECTS shallow-angle light downward rather than scattering it, so the light is kept andput to use. AND THAT IS WHY IT IS WRONG HERE: the moulded pattern is visible and reads as a workplacefitting however warm the light through it is. In a bar, take OPAL or FROSTED.
Supplied and supported by Lights For You.
What does “prismatic” actually mean?
It is a clear panel moulded with a repeating pattern of small prisms, and each prism refracts the light passing through it, bending steep rays back towards the vertical. So it does not scatter light the way frosted does it redirects it. Output that would have left at a shallow angle leaves closer to straight down, which is why it is the office finish: the reflection you see in a monitor is shallow-angle light from a fitting behind you, and a prismatic panel sends most of it onto the desk instead.
Why is prismatic wrong in a bar?
Because the moulded pattern is visible. It gives a faceted, technical-looking face that reads as a workplace fitting no matter how warm the light through it is, which undoes the atmosphere the 3000K was chosen for. Take opal or frosted instead: you give up the glare control and gain a fitting that belongs in the room.
How do the glare-controlling finishes differ?
By what happens to the light. Frosted and opal scatter shallow-angle light it is kept but still emitted at that angle. Prismatic redirects it downward, so it is kept and put to use. A honeycomb absorbs it, so it is lost. Prismatic is therefore the efficient answer and honeycomb the thorough one, and which to choose depends on how strict the requirement is. With no UGR figure published for either, that is a judgement rather than a calculation.
Which finish over a bar?
Opal if the fitting sits near eye level, since it gives the most uniform face; frosted above head height for more output. Not prismatic, for the reason above. Not clear, which is an undiffused source over seated guests. The black diffuser is an option if you want the fitting to disappear when it is off.
Do I need a dimmer?
Yes. 3060 lumens at full output is service light right for prep and stocktake and too much during service. Dimmed to roughly a quarter it becomes evening light. It ships with an integral dimmable driver and DALI is available on request, but the minimum level is not published. Tell us your control and the level you want during service.
Why CRI90 over a bar?
Because warm light and accurate colour usually pull against each other, and most commercial linear at 3000K publishes CRI80 where reds flatten. Over a bar that is exactly what shows in a garnish, a cocktail or a cut of meat. CRI90 means the fitting that disappears against a dark ceiling also renders the food properly.
Will 1.7m suit my bar?
It suits a bar or communal table of about 2.5m roughly two-thirds the length, which lights evenly without overhanging the ends. For a longer bar, two with a deliberate gap read better than one fitting stretched, and the gap should be half a fitting length or more.
Only logged in customers who have purchased this product may leave a review.
We offer fast and reliable shipping worldwide. All orders are carefully packaged and shipped within 1–3 business days after payment confirmation.
Standard shipping, expedited shipping and express delivery options are available at checkout. Delivery time depends on your destination country and local logistics.