Your shopping cart is empty!
The Domus SHADOW 2LT W/B is an up-and-down exterior walllight 12V MR16, IP65, fixed beams,235W maximum, in seven finishes.
Lamp (Included): KEY-GU10-TRIO (240V) KEY-MR16-TRIO (12V) correct and complete. All three two-light sheets in this family name bothlamps and map each to its voltage; none of the three one-light sheets does. That clean split is what identifies the one-light documents as a stale revision rather than awrong one. For this product it means the sheet reads as published: 12V, so MR16,and the lamps are included.
The two beams create an hourglass of light on the wall a bright triangle above andbelow with a narrow waist at the fitting. THAT SHAPE IS THE EFFECT, so the wallmaterial matters more than with most fittings. On render or smooth masonry it reads as aclean graphic; on textured brick or stone it grazes the surface and picks up every irregularity, which canbe beautiful or busy depending on the wall. If the wall is uneven and you do not wantthat emphasised, mount the fitting further from the surface or choose a downward-onlyversion.
The practical case is the same as for the adjustable two-light: one hole, one cable, one sealfor two beams. On masonry or rendered facades every penetration is a cost and apotential water path, so halving them matters. 2 35W is the holder ceiling; theincluded tricolour MR16 lamps draw far less, typically 5 to 7W each size the 12V driver on the real load with 20 to 30% headroom, not on themaximum.
316 stainless steel and copper are solid; titanium silver is anodised; black and white arepowder-coated aluminium. A powder coat is a film that corrodes from any chip; solidfinishes have no film to fail. Within a few kilometres of surf, 316 is the sensibledefault. Copper patinas to brown and then green a feature if intended and acomplaint if not.
| Specification | Value |
|---|---|
| Lamp base | MR16 at 12V the sheet maps both correctly |
| Lamps included | 2 tricolour, switchable |
| Beams | Fixed up and down no adjustment |
| Supply | 12V DC driver required |
| Max per head | 35W holder ceiling expect 57W actual |
| IP rating | IP65 |
| Mounting height | 1.82.2m and consistent along a facade |
| Penetrations | One hole, one cable, one seal for two beams |
| Finishes | 7 316 stainless and copper solid |
| Warranty | 3 years sheet prose; not on the record |
Up-and-down exterior wall light, IP65. 12V DC, MR16 lamp base, 2 35W maximum holderrating. Two tricolour lamps included. Fixed beams. Seven finishes. 12V DC driver required. 3-yearwarranty. ITS SHEET NAMES BOTH LAMPS CORRECTLY, like every other two-light document in this family allthree do, and none of the three one-light sheets does, which is the clean split identifying the one-lightdocuments as a stale revision. FIXED RATHER THAN ADJUSTABLE IS A DELIBERATE CHOICE: an adjustable headis a moving joint exposed to weather, and on a facade nobody will ever re-aim, it carries risk withoutbenefit. Fixed up/down fittings are the ones still working in year fifteen. THE HOURGLASS OF LIGHT IS THEEFFECT, so the wall material matters more than usual.
Supplied and supported by Lights For You.
Does its sheet name the right lamp?
Yes “Lamp (Included): KEY-GU10-TRIO (240V) KEY-MR16-TRIO (12V)”, naming both and mapping each to its voltage. All three two-light sheets in this family do that and none of the three one-light sheets does, which is the clean split identifying the one-light documents as a stale revision rather than a wrong one.
Why choose fixed over adjustable?
Fewer joints, and a beam that cannot be knocked out of alignment. An adjustable head is a moving joint exposed to weather, and on a facade where nobody will ever re-aim the fitting it is a mechanism carrying risk without carrying benefit. Fixed up/down fittings are the ones still doing their job in year fifteen.
What is the downside?
What you get is what you get. The wall wash is determined by the fitting’s position and nothing else, so the mounting height decides the result there is no correcting it afterwards.
What height should I mount it at?
Around 1.8 to 2.2 metres. Lower and the downward pool is small and the upward beam short; higher and the light is above the eye and the wall wash loses its top edge. Mount them at a consistent height along a facade unevenly spaced or unevenly high up/down lights are conspicuous at night in a way they never are on a drawing.
What does the light actually look like?
An hourglass a bright triangle above and below the fitting with a narrow waist at it. That shape is the effect, so the wall material matters more than with most fittings. On render or smooth masonry it reads as a clean graphic; on textured brick or stone it grazes the surface and picks up every irregularity, which can be beautiful or busy depending on the wall.
What if the wall is uneven?
Mount the fitting further from the surface, or choose a downward-only version. Grazing light is unforgiving it will show every mortar line and every patch, which is exactly what some facades want and some very much do not.
What driver do I need?
2 35W is the holder ceiling, but the included tricolour MR16 lamps draw far less typically 5 to 7W each. Size the 12V driver on the real load with 20 to 30% headroom rather than on the maximum. A driver sized for 70W when the load is 14W works, but it is money and space spent for nothing.
Only logged in customers who have purchased this product may leave a review.
We offer fast and reliable shipping worldwide. All orders are carefully packaged and shipped within 1–3 business days after payment confirmation.
Standard shipping, expedited shipping and express delivery options are available at checkout. Delivery time depends on your destination country and local logistics.