The Halon ST1 is a 24V exterior LED step light insolid brass or 316 stainless steel with glass 1W giving 65lm at 3000K, CRI above 90,IP67 in antique brass, natural brass or stainless steel.

It runs on 24 volts, so it needs a transformer and we stockthem. A 240V-to-24V supply is required andno Telbix fitting in this range records one as supplied. We sell anoutdoor 24V transformer in 60W and 200W, bothIP68. At 1W each these are the cheapest fittings in the rangeto run: a 60W transformer would drive dozens. Tell us how many steps you arelighting and we will size it.

IP67 on a step light and that is the reason to choose it

IP67 means dust-tight and rated for temporary immersion. Not splashing, not jets submersion. On a step that matters more than it sounds:water runs down stairs and pools against the riser, and a fitting set into that riserwill sit in standing water after heavy rain.

Compare the Jora step light in this range, which is IP54 splash-rated only, and suited to covered steps. The Halon atIP67 is rated for fully exposed steps that take run-off. If yourstairs are outside and uncovered, this is the one.

Solid brass or 316 marine stainless

Our record lists Glass alone. The body issolid brass or 316 stainless steel and set into a wetriser, taking run-off and cleaning, that is the only sensible construction.316 is the marine grade, with added molybdenum to resist salt;brass weathers rather than corrodes.

Three finishes and one of them ages

Antique brass starts dark and stays close to it.Natural brass is unlacquered and will patina to a soft brown-gold.316 stainless stays silver. On a run of steps that decision compounds youare choosing whether the whole flight changes together over the years.

Two cutouts, and it must be decided before the concrete

46mm with the canister, 35mm without. The canister is the sleeve setinto the step; whether you use it decides the hole size. The face is53mm by 51mm and it weighs 0.35kg.Confirm with your builder which arrangement they are using before the steps arepoured or the treads cut it cannot be changed afterwards.

65 lumens, and that is correct for a step

A step light should show you the edge of a tread withoutdazzling you on the way down. 65lm is deliberately small, andthe CRI above 90 is what makes it worth having: stone, timber andconcrete keep their real colour rather than going grey, so you see the step as it actuallyis.

Where it works

• Fully exposed exterior steps IP67 handles run-off and pooling.
• Deck and concrete risers.
• Coastal installations 316 stainless or solid brass.
• Confirm the cutout with your builder before the steps are poured.
• Needs a 24V transformer we stock 60W and 200W.

Specifying it

53mm by 51mm face, cutout46mm with the canister or 35mm without,0.35kg, tail 1,000mm, insolid brass or 316 stainless steel with glass. Integrated1W LED giving 65lm at 3000K, included,CRI>90, not dimmable.24V a transformer is required and none is supplied; we stock 60W and200W. ClassIII low voltage,IP67 dust-tight and rated for temporary immersion. Warranty is three years,as a replacement warranty.

Supplied and supported by Lights For You.

Questions

Can it go on uncovered steps?

Yes that is the reason to choose it. IP67 is dust-tight and rated for temporary immersion, which matters on a step because water runs down stairs and pools against the riser. The Jora step light in this range is IP54, splash-rated only, and suited to covered steps.

Does it connect to a normal circuit?

No 24 volts, so a 240V-to-24V transformer is required and none is supplied. We stock 60W and 200W outdoor transformers. At 1W each these are the cheapest fittings here to run a 60W transformer would drive dozens.

What cutout does it need?

46mm with the canister, 35mm without. The canister is the sleeve set into the step, and whether you use it decides the hole size. Confirm with your builder before the steps are poured or the treads cut it cannot be changed afterwards.

What is it made of?

Solid brass or 316 stainless steel with glass. Our record lists Glass alone. Set into a wet riser taking run-off and cleaning, that is the only sensible construction.

Which finish should I choose?

Antique brass starts dark and stays close to it; natural brass is unlacquered and patinas to a soft brown-gold; 316 stainless stays silver. On a run of steps the decision compounds you are choosing whether the whole flight changes together over the years.

Is 65 lumens enough?

For a step, yes, and more would be worse it should show the edge of a tread without dazzling you on the way down. The CRI above 90 is what makes it worth having: stone, timber and concrete keep their real colour rather than going grey.

How does it compare to the Halon inground light?

Same family, same 24V and IP67, same materials. The inground is 45mm round at 110lm for setting into a surface you walk over; this step light is 53 by 51mm at 65lm for setting into a riser.