Your shopping cart is empty!
The HV10391T is the Luz up-and-down wall pillar light in poly powder coated white aluminium the two-lamp body, with one GU10 firing up the wall and one down. White is the finish that disappears against light render, painted brick or a pale rammed-earth pier: in daylight you see the wall, and after dark you see the two cones of light rather than the fitting making them.
Havit supplies two 9-in-1 tri-colour GU10 globes with the fitting, each switchable for colour and for output. The figures are per lamp and not a total: 240560lm at 3000K, 255595lm at 4000K and 270630lm at 5500K, where the bottom of each range is the globes 3W setting and the top is 7W. Output rises as the colour temperature climbs, so the brightest this fitting goes is 5500K at 7W. The beam is 60, which comes from the supplied globe rather than the housing a narrower, more deliberate cone than the 120 globes used elsewhere in Havits wall range.
The switches are on the side of each globe, so changing colour or wattage means twisting off a cover and taking the globe out. Havit ships it preset to 3000K at 7W. The lampholder is a standard GU10 and the globes are replaceable, to a maximum of 35W per lampholder.
Havit is explicit: fix the backing plate, then seal every hole in it including the cable entry and the screw holes, or the warranty is void. The o-rings and seals must all be correctly seated, silicone goes round the base plate at the wall, and modifying the fitting voids the warranty too. The IP65 and IK10 ratings assume that work was done. It is 240V AC mains with no driver or transformer, and Class1, so it requires an earth.
This is an aluminium fitting, and Havits current instructions state that aluminium and 304SS fittings must not be installed within 5km of any salt water environment. Within that distance, the solid brass HV10591T is the version to specify. It stands 300mm tall with a 60mm aperture at each end, and the backing plate takes four 4mm fixings around a 13mm cable entry. We do not publish a width or a wall projection for this listing: Havits drawing prints those numbers without labels and this products own record holds neither figure, so we would be guessing. The dimensioned drawing is in the data sheet attached here.
It is Triac dimmable, with Havits HV9625 300W dial dimmer named as the compatible control. Every figure above was taken from Havits own dated documents for this part number by the Lights For You team call us if you want the white checked against a paint or render sample first.
Is this fitting aluminium or stainless steel?
Aluminium, poly powder coated white. Both of Havits dated documents for this part number say so the data sheets Material row and the installation sheets model-by-model table. The stainless steel in the description refers to the grub screws that hold the fitting to its backing plate, not to the body.
Are the lumen figures for one lamp or for both?
One lamp. Havit prints 2 240560lm, so each globe produces the stated range and the fitting produces double across its two directions. We do not publish a summed number, because it hides how much light goes up and how much goes down.
Are globes supplied?
Yes two 9-in-1 tri-colour GU10 globes, listed in the data sheets Included LED column and on Havits own page for this model. They are switchable between 3000K, 4000K and 5500K and between 3W, 5W and 7W.
How close to the coast can it go?
No closer than 5km from any salt water environment Havits current instructions exclude aluminium and 304SS fittings inside that distance, and this is aluminium. The solid brass Luz, HV10591T, is not named by that clause and is the coastal choice.
What is the beam angle?
60, set by the supplied 9-in-1 GU10 globe rather than by the fitting itself. Because the globes are replaceable, a different GU10 with a different beam angle will change it the housing has no beam angle of its own.
How wide is it?
We do not publish a width for this listing. Havits drawing gives the remaining dimensions as unlabelled numbers and this products own record holds no width figure, so any number we quoted would be inferred rather than sourced. The 300mm height is published, and the dimensioned drawing is on this page.
What is the warranty, and how do I keep it?
3 years replacement for items ordered after 01/01/22. To keep it: seal the backing plate including cable entry and screw holes, keep all o-rings and seals in place, do not modify the fitting, and have it installed by a licensed electrician to AS/NZS 3000.
Only logged in customers who have purchased this product may leave a review.
We offer fast and reliable shipping worldwide. All orders are carefully packaged and shipped within 1–3 business days after payment confirmation.
Standard shipping, expedited shipping and express delivery options are available at checkout. Delivery time depends on your destination country and local logistics.