The Tivah single adjustable is a wall and pillar light that aims 90 of tilt and 270 ofswivel on a black powder-coated backing plate so it is specified when the thing you want to lightis not directly below the fitting. A tree, a house number, a gate leaf, the face of a pillar at an angle tothe wall: all cases where a fixed downlight points at nothing useful.

Three versions, and the choice is electrical

This listing carries three order codes and they are genuinely different products, not finishes.HV1225T has a built-in LED and needs no globe at all. HV1227GU10T takes amains-voltage GU10 globe on 240V AC. HV1227MR16T takes a 12V DC MR16 globe andtherefore requires a 12V DC LED driver. Decide the electrical arrangement before the finish: thebuilt-in version is the simplest to install and never needs a lamp; the GU10 lets you change the globewithout touching the fitting; the MR16 gives you a low-voltage circuit with no earth at the fitting, whichsuits a long garden run fed from one central driver.

Where it works

• Driveway and gate pillars, one either side, angled to wash the pillar face rather than the ground.
• Uplighting a tree or a rendered blade wall from a fixed point on an adjacent wall.
• House numbers, letterboxes and signage that need light aimed at them specifically.
• Rain-exposed positions IP65 covers direct rain and hose wash-down. Near salt water, read Havits exclusion below.

Specifying it

Tri-colour switching covers 3000K, 4000K and 5500K. Output depends on which versionyou buy: the built-in 3W LED gives 270lm, 285lm and 300lm across the three settings,while the globe versions depend on the lamp you fit. The body is powder-coated aluminium in textured blackwith a high-output reflector, IP65, and CRI is above80. Neither globe version is dimmable withthe globes supplied if dimming matters, confirm the lamp you intend to fit is dimmable andthat the dimmer suits it. The MR16 version must never be connected directly to 240V.

Globe wattage limits

If you are fitting your own lamp, do not exceed the sockets limit: the maximum the 240V GU10socket accepts is 35W, and the maximum the 12V MR16 socket accepts is 20W. Those arethermal limits on the fitting, not a recommendation, and an oversized lamp will cook the housing.

Supplied and supported by Lights For You. Order all the fittings for one entrance together thetextured black powder coat is matched per production run, and the three versions share the same body, soyou can mix a built-in fitting with a GU10 one on the same elevation and they will look identical.

Coastal siting Havits condition

Havits installation instructions for this fitting state that aluminium and 304 stainless steel fittings must not be installed within 5 km of any salt water environment. That is a condition on where the fitting may go, and it sits beside the IP rating rather than inside it: a fitting can be rated for direct rain and still fall outside this rule, because the issue is salt carried in the air rather than water landing on the surface. If your site is inside that zone, talk to us before you specify it Lights For You can point you at a fitting whose material Havit does not name here.

Questions

What is the difference between the three order codes?

HV1225T has a built-in LED and takes no globe. HV1227GU10T takes a 240V GU10 globe. HV1227MR16T takes a 12V DC MR16 globe and needs a 12V DC driver.

Which one needs a driver?

Only HV1227MR16T. It is 12V DC and requires a 12V DC LED driver sized for every fitting on the circuit. It must never be wired directly to 240V.

How far does it move?

90 of tilt and 270 of swivel, so it can be aimed at a pillar face, a tree or signage rather than straight down.

What is the maximum globe wattage?

35W for the 240V GU10 socket and 20W for the 12V MR16 socket. These are limits on the fitting, not suggestions.

How bright is the built-in version?

270lm at 3000K, 285lm at 4000K and 300lm at 5500K, from a 3W LED.

Can it be dimmed?

Not with the globes supplied. If you need dimming, fit a dimmable lamp of your own and confirm the dimmer suits it and for the MR16 version, that the driver is dimmable too.

Is it suitable near the coast?

IP65 covers direct rain and wash-down, but Havit goes further than the rating: its installation instructions say aluminium and 304 stainless steel fittings must not be installed within 5 km of any salt water environment. Within sight of surf, specify the 316 stainless steel version of the Tivah instead.

What is the warranty?

Three years, as a replacement warranty, on all three order codes.