Welcome To our shop !

Pinta LED Step Light Eyelid 316 Stainless Steel

$50.5 $101
SKU: KO80391101586
Availability: in Stock

Pinta in 316 stainless steel is a round eyelid step light,105mm across, with a tempered glass lens and a marine-grade body. 316 is thestainless grade specified for salt exposure, so…

Qty:

Pinta in 316 stainless steel is a round eyelid step light,105mm across, with a tempered glass lens and a marine-grade body. 316 is thestainless grade specified for salt exposure, so this is the version for a coastal orpoolside wall where powder-coated aluminium eventually blisters. The eyelid shroud aimsthe light downwards and keeps the source out of direct view. The important thing aboutthis listing is that the four part numbers are not finishes theyare different voltages and different lamp arrangements.

The choice to make: which part number
  • HV2901 240V AC, takes a G9 globe up to25W. Wires straight to mains, no driver. No globe is supplied, andonly a G9 will fit a G4 or an LED module will not.
  • HV2902 12V, takes a G4 globe up to20W. Requires a 12V DC LED driver andno globe is supplied. Only a G4 fits.
  • HV2903T 240V AC with a built-in 2.3Wtri-colour LED. Straight to mains, no driver, no globe needed or possible.
  • HV2904T 12V DC with the same built-in 2.3W LED.Requires a 12V DC LED driver and mustnever be connected directly to 240V.

On the two LED versions the tri-colour output is 160lm at 3000K, 170lm at4000K and 180lm at 5500K, selected at install. The G9 and G4 versions producewhatever globe you fit, which is their advantage and their catch: you buy the lampseparately and you can re-lamp later.

Where it works
  • Coastal and waterfront walls 316 stainless is the reason to choose this over an aluminium fitting.
  • Pool surrounds, where chlorine and salt both attack painted finishes.
  • Exposed garden stairs and paths IP65 for direct rain, with the eyelid controlling glare.
  • Heritage and hardware-matched exteriors where a plain stainless round suits the detailing.
Specifying it

Wired in parallel, IP65, and not dimmable in any version if a dimmed circuit ispart of the brief, this is the wrong fitting. On either 12V part number, keep eachfitting within 25m of its driver, which is a warranty limit, andsize the driver for the full circuit load. Even marine-grade stainless benefits from anoccasional fresh-water rinse in salt air; tea-staining is cosmetic rather than structuralcorrosion. Licensed electrician only.

Backed by a 3-year replacement warranty.

Supplied and supported by Lights For You; because the four Pinta part numbers differ in voltage and lamp base, tell us your circuit and we will confirm which one to order.

Earthing and protection class

This listing sells more than one supply, and the earthing requirement is not the same on both. Check which part number you are wiring before you start.

  • HV2901, HV2903T run on 240 V AC mains and are Protection Class 1 an earth is required at the fitting. Havit’s installation sheet has the installer connect the earth conductor first, then live and neutral.
  • HV2902, HV2904T run on 12 V DC and are Protection Class 3 no earth is required at the fitting. The isolation comes from the LED driver rather than from an earth conductor, and these part numbers must never be connected directly to 240 V.
Questions

Which part number do I need?

If you are wiring to mains, choose HV2901 (G9 globe, suppliedseparately) or HV2903T (built-in LED). On a low-voltage circuit choose HV2902 (G4 globe)or HV2904T (built-in LED). The built-in LED versions are the simpler specification.

Is a globe included?

Not on HV2901 or HV2902 those are supplied without a lamp andyou buy the globe separately. HV2903T and HV2904T need no globe at all; the LED is builtin and cannot be replaced.

Can I put a G4 globe in the G9 version, or the reverse?

No. The base is fixed by the part number: HV2901 takes G9 only,HV2902 takes G4 only. A different base will not fit, and the two are on differentvoltages besides.

Which versions need a driver?

HV2902 and HV2904T, both 12V each needs a 12V DCLED driver and must never be connected directly to 240V. HV2901 and HV2903T are240V and wire straight to mains.

How far can a 12V fitting sit from its driver?

Up to 25m. Outside that limit the warranty does not apply, andlong thin runs cause voltage drop that reads as dimming at the far end.

Can Pinta be dimmed?

No. None of the four versions is dimmable. Choose a fitting specifiedas dimmable if that is a requirement.

Only logged in customers who have purchased this product may leave a review.

Shipping policy for our store

We offer fast and reliable shipping worldwide. All orders are carefully packaged and shipped within 1–3 business days after payment confirmation.

  • Fast shipping within 1-3 business days
  • Free shipping on orders over $40
  • 30 days money back guarantee
  • 24/7 online customer support
  • Secure packaging & safe delivery

Standard shipping, expedited shipping and express delivery options are available at checkout. Delivery time depends on your destination country and local logistics.