The Versa Square is a 100mm cube that lights both up and down, and its distinguishing feature isthat the beam angle itself adjusts anywhere from a tight 1 slot to a broad 120 spread.That is unusual on an up/down fitting and it is the whole reason to choose it: you set the effect on site,against the actual wall, rather than committing to it at the point of order.

Setting the beam is the job

Wound tight, the two 3W LEDs throw narrow blades of light up and down the wall crisp,graphic, and very dependent on the wall being flat and clean, because a narrow beam shows every ripple inrender. Opened to 120 it becomes a soft double wash that forgives an uneven surface and reads asgeneral light rather than an effect. Set it before the scaffold comes down; adjusting later means gettingback up to the fitting.

Where it works

• Entry and courtyard walls in pairs or runs, where the symmetry of up-and-down suits the architecture.
• Feature walls of smooth render or off-form concrete, with the beam wound in for a graphic line.
• Textured brick or blockwork, with the beam opened up so the texture is lit rather than raked.
• Rain-exposed elevations IP65 covers direct rain and hose wash-down. Near salt water, read Havits exclusion below.

Specifying it

Two 3W LEDs are built in and supplied with the fitting, one facing up and one down; there is noglobe and no socket. Tri-colour switching gives 220lm at 3000K, 230lm at 4000K and240lm at 5500K a deliberately modest output, because this is an accent fitting forwall effect rather than area lighting. It runs on 240V AC with no separate driver, wires in parallel,is not dimmable, and CRI is above 80. The body is 100100100mmpoly powder coated aluminium, IP65, in white or black at the same price.

Supplied and supported by Lights For You. Because the beam is adjustable, order one fitting first if youare unsure of the effect on your particular wall the difference between 1 and 120 ontextured render is dramatic.

Coastal siting Havits condition

Havits installation instructions for this fitting state that aluminium and 304 stainless steel fittings must not be installed within 5 km of any salt water environment. That is a condition on where the fitting may go, and it sits beside the IP rating rather than inside it: a fitting can be rated for direct rain and still fall outside this rule, because the issue is salt carried in the air rather than water landing on the surface. If your site is inside that zone, talk to us before you specify it Lights For You can point you at a fitting whose material Havit does not name here.

Earthing and protection class

This fitting runs on 240 V AC mains and is Protection Class 1 an earth is required at the fitting. Havit’s installation sheet has the installer connect the earth conductor first, then live and neutral.

Questions

How adjustable is the beam?

From roughly 1 to 120, set by hand at the fitting. Narrow gives graphic blades of light; wide gives a soft double wash.

Does it need a driver?

No. It runs on 240V AC with the driver built in, and wires in parallel with other fittings on the circuit.

How bright is it?

220lm at 3000K, 230lm at 4000K and 240lm at 5500K, from two 3W LEDs. It is an accent fitting, not area lighting.

Are the LEDs replaceable?

No. Both 3W LEDs are built in and supplied with the fitting. There is no globe or socket.

Can it be dimmed?

No. This fitting is not dimmable.

Is it suitable for a coastal wall?

IP65 covers direct rain and hose wash-down, so it suits exposed and rain-hit walls. Salt is a separate question, and Havits condition is firmer than the rating: aluminium and 304 stainless steel fittings must not be installed within 5 km of any salt water environment. Inside that zone, specify a 316 stainless fitting instead of powder-coated aluminium.

What is the warranty?

Three years, as a replacement warranty.